barge capping colorbond corr - Compare The Best barge capping colorbond corr Prices In Australia | GetPrice
You searched

barge capping colorbond corr

Showing 1 - 20 of 56 results
Sort:
  1. Barge Capping Colorbond - Suit Corrugated roofing

    $10.68
    + Shipping
  2. Barge capping is the typical flashing piece used to finish off any roofing profile with the edge of the wall and runs down the length of the roof sheeting it is finishing off. Typically the barge flashing should be at least 40-50mm longer than the specified roof length to allow for the angle cutting at the top of the roof line and even longer if being used to continue past the gutter at the end of the roof sheets.

    $14.15
    + Shipping
  3. Barge flashing to suit Kliplok roofing profile

    $10.68
    + Shipping
  4. Barge Capping Colorbond - Suit Trimdek & Spandek

    $10.68
    + Shipping
  5. 50mm diameter Barge roll to finish off the roof sheeting at the ends of a vertical wall

    $27.15
    + Shipping
  6. Gutter flashing to go over a timber fascia board to prevent backflow of water behind the fascia

    $13.30
    + Shipping
  7. Image shows a left hand barge mould The Clickfast Fascia and Gutter system is one of the few products in Australia to receive the coveted classic design award. Your guarantee of excellence. Unlike timber you will not experience warping bowing knots or cracking. Instead you will receive a consistent trouble free product without the variability of price and quality often found with timber. The system uses side-fix fascia brackets which can be nailed into the side of the rafter rather than the end. Nailing into the side grain of rafters is far stronger than nailing into the end grain which may open up releasing the nail. The fascia then slides onto the side-fix rafter bracket allowing for free horizontal movement and uniform expansion and contraction and minimising distortion. The revolutionary suspension clip allows you to select the amount of fall the gutter receives. This high strength spring-clip is notched to allow for the clip to attach to the suspension rib found on all Stratco gutters. Gutters can even be adjusted later to correct house settlement.

    $4.35
    + Shipping
  8. Barge roll flashings are a combination of both the standard barge flashing and the barge roll which offers a neat rolled edge to the length of the roof sheet but also runs across the top of the roof line to give a more detailed finish to the roof shape. Typically the barge roll flashing should be at least 40-50mm longer than the specified roof length to allow for the angle cutting at the top of the roof line and even longer if being used to continue past the gutter at the end of the roof sheets.

    $34.86
    + Shipping
  9. Baarge Capping Polycarbonate (110x130, 90°) 3 meter length

    $66.00
    + Shipping
  10. Barge roll capping to blend roof sheeting to other areas where barge rolls are being used

    $38.98
    + Shipping
  11. Barge capping is the flashing piece used at the very end of a roof thats the gap between the roof sheet and the vertical wall surface Supplied in clear only Supplied in lengths : 3000 3600 4200 4800 6000mm

    $17.32
    + Shipping
  12. Barge capping is the typical flashing piece used to finish off any roofing profile with the edge of the wall and runs down the length of the roof sheeting it is finishing off. Typically the barge flashing should be at least 40-50mm longer than the specified roof length to allow for the angle cutting at the top of the roof line and even longer if being used to continue past the gutter at the end of the roof sheets.

    $11.00
    + Shipping
  13. Standard ridge capping to suit Kliplok, Longline and Integrity style roof sheeting

    $18.29
    + Shipping
  14. Ridge capping is the flashing that is used at the very top of any gable type roof. Standard dimensions are 20/180/180/20mm - if you are needing customised dimensions please refer to the custom flashings details.

    $13.14
    + Shipping
  15. LYSAGHT INTEGRITY 820 has the additiol feature of a rib cap otherwise known as style capping strip. This cap is optiol and used when concealed fixing is required. When using the style cap a special clip is required. The cap fits over the ribs to hide the screw fixings and to add extra boldness to the profile. The style capping strips can be ordered in custom cut lengths. However special transportation and handling may be required for long lengths.

    $6.36
    + Shipping
Back to top

Recently Viewed Roof & Gutter


Connect
Getprice compares prices across all of your favourite products Australia-wide, covering all major cities including Sydney, Melbourne, Perth, Canberra and Brisbane.
Getprice compares prices across Sydney, Melbourne, Perth, Canberra and Brisbane.