copper pipe - Compare Cheap copper pipe Prices & Save shopping in Australia
You searched

copper pipe

Showing 1 - 20 of 82 results
Sort:
  1. Cdi Meters Cdi 5200 Flow Meter For Copper Pipes (Nominal Pipe Size 1")

    The CDI 5200 clamps onto a pipe, with two flow-sensing probes projecting into the pipe through 3/16-in. drilled holes. It seals directly to the pipe; no cutting or welding is required for installation. Because each flowmeter is made and calibrated for a specific size of pipe, the digital display indicates flow directly, with no setup or adjustment. The meter measures flow by maintaining one probe warmer than the other. It determines the mass flow rate from the amount of heat required. The flow rate, in scfm or equivalent units, is shown on a large, four-digit display; a 4-20 mA output and a pulse output permit remote dis-play, totalizing and data collection. Features: - Easy to install - Two-rings - No moving parts - Weather resistant and surge protected - Milliamp output - Pulse output convertible to threshold output - User-configurable scaling, filtering and units of measureSpecifications: - Accuracy: 5 percent of reading plus 1 percent of range for flows from 10 percent to 100 percent of indicated range at air temperatures between 20 and 120 degrees Fahrenheit.- Fluids: Compressed Air, Nitrogen - Range: 200 scfm- Operating Pressure (steel and copper): 200 psig maximum - Input power: 250 mA at 24 Vdc- Output resistance: 600 Ohms max.- Exposed Materials: Stainless steel, gold, thermal epoxy and Viton (seal)- Display: Four-digit LED display- Response time: One second to 63 percent of change in value at flows above 30 percent of range

    $984.50
    FREE shipping
    Go to shop
  2. Cdi Meters Cdi6200, Compressed Air Using Copper Pipes (1-1.25")

    The CDI 6200 series was designed for monitoring the flow rate of compressed air systems. The flowmeter clamps onto a pipe, with two flow-sensing probes projecting into the pipe through 3/16-in. drilled holes. It seals directly to the pipe; no cutting or welding is required for installation. Because each flowmeter is made and calibrated for a specific size of pipe, the display indicates flow directly, with no setup or adjustment. The meter measures flow by maintaining one probe warmer than the other. It calculates the mass velocity from the amount of heat required, and then calculates the flow on the basis of pipe area. The flow rate, in scfm, is shown on a large, four-digit display; a 4-20 mA output and a pulse output permit remote display, totalizing and data collection. Features: - Easy to install - Housing and display rotate to suit piping orientation - IP-66 rating; suitable for wet locations - Milliamp and pulse outputs - Optional RS-485 output for networking Specifications: - Accuracy: 5 percent of reading plus 1 percent of range for flows from 10 percent to 100 percent of indicated range at air temperatures between 20 and 120 degrees Fahrenheit. - Fluids: Compressed Air, Nitrogen - Range: 200 scfm - Operating Pressure (steel and copper): 200 psig maximum - Input power: 250 mA at 24 Vdc - Output resistance: 400 Ohms max. - Exposed Materials: Stainless steel, gold, thermal epoxy and Viton (seal) - Display: Four-digit LED display - Response time: One second to 63 percent of change in value at flows above 30 percent of range

    $1,182.50
    FREE shipping
    Go to shop
  3. Brilliant 42W DOUGLAS Pipe Floor Lamp - Copper

    Brilliant 42W DOUGLAS Pipe Floor Lamp - Copper Model Number:18972/18 SKU:BL-1897218 QUICK FACTS: Floor Lamp Width: 230mm x Height: 1560mm Colour Trim: Copper Suitable for Interiors FEATURES: 240V - 42W max - E27 CFL Globe Warranty: 12 Months DESCRIPTION: Born from inspiration of industrial pipes theDouglas floor lamp pushes the industrial trendinto an era of elegance. Well proportionedand sophisticated lines provide the perfectopportunity to frame this seasons trendingdecorative globe Why OzLighting? Australian company, selling only certified & tested product. Lighting curated to meet your needs. Expert customer service. NEED HELP? Email: sales@ozlighting.com.au and one of our expert advisers will be in touch with you.

    $110.00
    + Shipping
    Go to shop
  4. Brilliant 42W DOUGLAS Pipe Table Lamp - Copper

    Brilliant 42W DOUGLAS Pipe Table Lamp - Gold Model Number:18969/18 SKU:BL-1896918 QUICK FACTS: Table Lamp Height: 560mm x Dia: 150mm Colour Trim: Copper Suitable for Interiors FEATURES: 240V - 42W max - E27 CFL Globe Warranty: 1 Year DESCRIPTION: Born from inspiration of industrial pipes theDouglas floor lamp pushes the industrial trendinto an era of elegance. Well proportionedand sophisticated lines provide the perfectopportunity to frame this seasons trendingdecorative globe Why OzLighting? Australian company, selling only certified & tested product. Lighting curated to meet your needs. Expert customer service. NEED HELP? Email: sales@ozlighting.com.au and one of our expert advisers will be in touch with you.

    $79.00
    + Shipping
    Go to shop
  5. Copper Pipe Kit 3/8"+5/8" x 3.5M

    Insulated copper tube piping kits For split air conditioner Pure copper, high quality, 3/8" + 5/8"

    $50.00
    + Shipping
    Go to shop
  6. Copper Pipe Kit 1/4"+1/2" x 3.5M

    Insulated copper tube piping kits For split air conditioner Pure copper, high quality, 1/4" + 1/2"

    $40.00
    + Shipping
    Go to shop
  7. Nylon Coated Saddle Clips for Copper Pipe - Pack of 20 1 1/2 inch

    Comes in a pack of 200 Available in various sizes from 1/2"" to 2""

    $11.75
    + Shipping
    Go to shop
  8. Copper Saddle Clips for Copper Pipe 5/16 inch

    Comes in a pack of 200 Available in various sizes from 1/4"" to 1""

    $29.45
    + Shipping
    Go to shop
  9. Copper Pipe Wall Light

    This copper pipe wall light will add a touch of industrial character to your shop, restaurant, cafe interior or home. This wall light will cast a beam of light light up or down a wall, beam or pillar. Its lamp holder can take either a halogen or LED GU10 bulb. It has a IP54 rating so is weather resistant and can be used for outdoor and indoor use. Features include: Industrial appeal Copper finish Non adjustable beam of light Weather resistant with an IP54 rating This copper pipe wall light takes a 35 watt GU10 bulb. with class of "tabs" --> Description Delivery Returns More Info with class of "tabs-content" --> About the Copper Pipe Wall Light: Made of copper material which adds to the lights industrial appeal, it will develop a natural patina over time. The lampholders is none adjustable but designed for casting light up and down a wall, beam or pillar, depending on which way it is installed. The copper shade tube is 55mm in diameter and 120mm long and gives a beam of light from its end. The wall plate is 80mm in diameter and 40mm high.The projection from the wall is 120mm. The lampholder takes a halogen or LED GU10 bulb. Max 35w. Bulb not included. It has an IP54 rating so is weather resistant. 240V. Fat Shack Vintage delivers Australia wide. From the tip to the tail and all the places in between… if you live in Australia we’ll get it to you. For a delivery quote, just select your desired products and proceed to the checkout where you will be able to enter your delivery postcode. It will then calculate the shipping price for your order based on your postcode and the items in your basket before you need to go ahead with the order and enter any personal details. All in stock items will be dispatched from our Melbourne warehouse within 2 business days from receipt of payment. Typical delivery times after dispatch are: * Melbourne - 2-3 business days * Sydney, Canberra, Adelaide - 4-5 business days * Brisbane, Tasmania – 5-6 business days * Darwin, Perth - Approximate

    $120.00
    + Shipping
    Go to shop
  10. Copper Pipe Spotlight

    Create an industrial lighting statement with this copper pipe light. It can be used as either a flush mount light or spotlight as it gives a beam of adjustable directional light. It is practical and stylish and has an IP54 rating so is weather resistant. It comes with a single halogen bulb. Add a touch of industrial character to shops, restaurants, cafe interiors or homes... anywhere a statement is required rather then just a light source. Features include: Adjustable spotlight Takes a GU10 bulb, either halogen or LED Copper finish Industrial design statement Weather resistant with an IP54 rating This spotlight takes a GU10 bulb. You can use your choice of halogen or LED bulbs in the fitting. with class of "tabs" --> Description Delivery Returns More Info with class of "tabs-content" --> About the Copper Pipe Spotlight: This halogen spotlight has an IP54 rating so is weather resistant and can be used for outdoor and indoor use. The copper shade tube is 55mm in diameter and 150mm long and gives a beam of directional light. So you can cast light where you want it to shine with adjustable halogen spotlight. Made of raw material; copper, which adds to the industrial feel. It will develop a natural patina over time. The lampholder takes a 35W GU10 bulb. Bulb not included. The wall plate is 78mm in diameter and 40mm high. 240V. Fat Shack Vintage delivers Australia wide. From the tip to the tail and all the places in between… if you live in Australia we’ll get it to you. For a delivery quote, just select your desired products and proceed to the checkout where you will be able to enter your delivery postcode. It will then calculate the shipping price for your order based on your postcode and the items in your basket before you need to go ahead with the order and enter any personal details. All in stock items will be dispatched from our Melbourne warehouse within 2 business days from receipt of payment. Typical delivery times after dispatch are: * Melbourne - 2-3 business da

    $125.00
    + Shipping
    Go to shop
  11. INSULATED PAIRED COPPER PIPE 6.35 x 12.7mm (1/4 x 1/2") - 20 metre lengths

    Insulated Paired Copper pipe 6.35 x 12.7mm (1/4 x 1/2") - 20 metre length

    $140.00
    + Shipping
    Go to shop
  12. INSULATED PAIRED COPPER PIPE 6.35 x 15.88mm (1/4 x 5/8") - 20 metre lengths

    Insulated Paired Copper pipe 6.35 x 15.88 mm (1/4 x 5/8") - 20 metre length

    $185.00
    + Shipping
    Go to shop
  13. Cdi Meters Cdi5400 Flow Meter For Copper Pipes (2")

    The CDI 5400 clamps onto a pipe, with two flow-sensing probes projecting into the pipe through 3/16-in. drilled holes. It seals directly to the pipe; no cutting or welding is required for installation. Because each flowmeter is made and calibrated for a specific size of pipe, the digital display indicates flow directly, with no setup or adjustment. The meter measures flow by maintaining one probe warmer than the other. It determines the mass flow rate from the amount of heat required. The flow rate, in scfm or equivalent units, is shown on a large, four-digit display; a 4-20 mA output and a pulse output permit remote dis-play, totalizing and data collection. Features: - Easy to install - No moving parts - Weather resistant and surge protected (new with Rev. 3) - Milliamp output - Pulse output convertible to threshold output - User-configurable scaling, filtering and units of measure - Optional RS-485 output for networking - Housing rotates to suit vertical or horizontal installation Specifications: - Accuracy: 5 percent of reading plus 1 percent of range for flows from 10 percent to 100 percent of indicated range at air temperatures between 20 and 120 degrees Fahrenheit - Fluids: Compressed air and Nitrogen - Range: 600 scfm - Operating pressure: 200 psig maximum on Sch. 40 steel and on Type L Copper below three inch; consult CDI for other materi-als and higher pressures. - Input power: 250 mA at 24 Vdc - Output resistance: 600 Ohms max. - Materials exposed to measured fluid: Stainless steel, gold, thermal epoxy and Viton (seal) - Ring material: Aluminum - Display: Four-digit LED display - Response time: One second to 63 percent of change in value at flows above 30 percent of range

    $1,267.20
    FREE shipping
    Go to shop
  14. Cdi Meters Cdi5400 Flow Meter For Copper Pipes (4")

    The CDI 5400 clamps onto a pipe, with two flow-sensing probes projecting into the pipe through 3/16-in. drilled holes. It seals directly to the pipe; no cutting or welding is required for installation. Because each flowmeter is made and calibrated for a specific size of pipe, the digital display indicates flow directly, with no setup or adjustment. The meter measures flow by maintaining one probe warmer than the other. It determines the mass flow rate from the amount of heat required. The flow rate, in scfm or equivalent units, is shown on a large, four-digit display; a 4-20 mA output and a pulse output permit remote dis-play, totalizing and data collection. Features: - Easy to install - No moving parts - Weather resistant and surge protected (new with Rev. 3) - Milliamp output - Pulse output convertible to threshold output - User-configurable scaling, filtering and units of measure - Optional RS-485 output for networking - Housing rotates to suit vertical or horizontal installation Specifications: - Accuracy: 5 percent of reading plus 1 percent of range for flows from 10 percent to 100 percent of indicated range at air temperatures between 20 and 120 degrees Fahrenheit - Fluids: Compressed air and Nitrogen - Range: 2000 scfm - Operating pressure: 200 psig maximum on Sch. 40 steel and on Type L Copper below three inch; consult CDI for other materi-als and higher pressures. - Input power: 250 mA at 24 Vdc - Output resistance: 600 Ohms max. - Materials exposed to measured fluid: Stainless steel, gold, thermal epoxy and Viton (seal) - Ring material: Aluminum - Display: Four-digit LED display - Response time: One second to 63 percent of change in value at flows above 30 percent of range

    $2,486.00
    FREE shipping
    Go to shop
  15. Cdi Meters Cdi25 Point-Of-Use Flowmeters For Copper Pipes (1")

    The CDI 25 represents a price-performance break-through in compressed-air metering. It fills a need for low-cost measurement of air usage by individual pieces of industrial equipment. It indicates leak-age and excessive usage locally with blinking lights, thereby eliminating the need for central monitoring and enabling equipment operators and maintenance mechanics to observe and respond to developing problems.The CDI 25 is based on CDI proven technology, but it has been streamlined to reduce cost, reduce material usage and facilitate installation. The meter measures flow by maintaining one of its two probes warmer than the other; it calculates flow from the amount of heat required. Current flow, as well as minimum, average and totalized flows can be seen on a four-digit display.Features: - Low cost permits monitoring of loads throughout an industrial plant- Alarm functions indicate when leakage has developed or usage has become excessive- Totalizing function allocates usage and cost- Complete flowmeter in one packageSpecifications: - Accuracy: 5 percent of reading plus 1 percent of range for flows from 10 percent to 100 percent of indicated range at air temperatures between 20 and 120 degrees Fahrenheit.- Fluids: Compressed Air, Nitrogen- Range: 200 scfm- Operating Pressure (steel and copper): 200 psig maximum- Input power: 250 mA at 24 Vdc- Output resistance: 600 Ohms max.- Exposed Materials: Stainless steel, gold, thermal epoxy and Viton (seal)- Display: Four-digit LED display- Response time: One second to 63 percent of change in value at flows above 30 percent of range

    $614.90
    FREE shipping
    Go to shop
  16. Cdi Meters Cdi5200 Flow Meter For Copper Pipes (1")

    The CDI 5200 clamps onto a pipe, with two flow-sensing probes projecting into the pipe through 3/16-in. drilled holes. It seals directly to the pipe; no cutting or welding is required for installation. Because each flowmeter is made and calibrated for a specific size of pipe, the digital display indicates flow directly, with no setup or adjustment. The meter measures flow by maintaining one probe warmer than the other. It determines the mass flow rate from the amount of heat required. The flow rate, in scfm or equivalent units, is shown on a large, four-digit display; a 4-20 mA output and a pulse output permit remote dis-play, totalizing and data collection. Features: - Easy to install - Two-rings - No moving parts - Weather resistant and surge protected - Milliamp output - Pulse output convertible to threshold output - User-configurable scaling, filtering and units of measureSpecifications: - Accuracy: 5 percent of reading plus 1 percent of range for flows from 10 percent to 100 percent of indicated range at air temperatures between 20 and 120 degrees Fahrenheit.- Fluids: Compressed Air, Nitrogen - Range: 200 scfm- Operating Pressure (steel and copper): 200 psig maximum - Input power: 250 mA at 24 Vdc- Output resistance: 600 Ohms max.- Exposed Materials: Stainless steel, gold, thermal epoxy and Viton (seal)- Display: Four-digit LED display- Response time: One second to 63 percent of change in value at flows above 30 percent of range

    $1,075.80
    FREE shipping
    Go to shop
  17. Cdi Meters Cdi5400 Flow Meter For Copper Pipes (2.5")

    The CDI 5400 clamps onto a pipe, with two flow-sensing probes projecting into the pipe through 3/16-in. drilled holes. It seals directly to the pipe; no cutting or welding is required for installation. Because each flowmeter is made and calibrated for a specific size of pipe, the digital display indicates flow directly, with no setup or adjustment. The meter measures flow by maintaining one probe warmer than the other. It determines the mass flow rate from the amount of heat required. The flow rate, in scfm or equivalent units, is shown on a large, four-digit display; a 4-20 mA output and a pulse output permit remote dis-play, totalizing and data collection. Features: - Easy to install - No moving parts - Weather resistant and surge protected (new with Rev. 3) - Milliamp output - Pulse output convertible to threshold output - User-configurable scaling, filtering and units of measure - Optional RS-485 output for networking - Housing rotates to suit vertical or horizontal installation Specifications: - Accuracy: 5 percent of reading plus 1 percent of range for flows from 10 percent to 100 percent of indicated range at air temperatures between 20 and 120 degrees Fahrenheit - Fluids: Compressed air and Nitrogen - Range: 800 scfm - Operating pressure: 200 psig maximum on Sch. 40 steel and on Type L Copper below three inch; consult CDI for other materi-als and higher pressures. - Input power: 250 mA at 24 Vdc - Output resistance: 600 Ohms max. - Materials exposed to measured fluid: Stainless steel, gold, thermal epoxy and Viton (seal) - Ring material: Aluminum - Display: Four-digit LED display - Response time: One second to 63 percent of change in value at flows above 30 percent of range

    $1,641.20
    FREE shipping
    Go to shop
  18. Cdi Meters Flow Meter -Compressed Air-Systems - Copper Pipes (1.5")

    The CDI 6200 series was designed for monitoring the flow rate of compressed air systems. The flowmeter clamps onto a pipe, with two flow-sensing probes projecting into the pipe through 3/16-in. drilled holes. It seals directly to the pipe; no cutting or welding is required for installation. Because each flowmeter is made and calibrated for a specific size of pipe, the display indicates flow directly, with no setup or adjustment. The meter measures flow by maintaining one probe warmer than the other. It calculates the mass velocity from the amount of heat required, and then calculates the flow on the basis of pipe area. The flow rate, in scfm, is shown on a large, four-digit display; a 4-20 mA output and a pulse output permit remote display, totalizing and data collection. Features: - Easy to install - Housing and display rotate to suit piping orientation - IP-66 rating; suitable for wet locations - Milliamp and pulse outputs - Optional RS-485 output for networking Specifications: - Accuracy: 5 percent of reading plus 1 percent of range for flows from 10 percent to 100 percent of indicated range at air temperatures between 20 and 120 degrees Fahrenheit. - Fluids: Compressed Air, Nitrogen - Range: 300 scfm - Operating Pressure (steel and copper): 200 psig maximum - Input power: 250 mA at 24 Vdc - Output resistance: 400 Ohms max. - Exposed Materials: Stainless steel, gold, thermal epoxy and Viton (seal) - Display: Four-digit LED display - Response time: One second to 63 percent of change in value at flows above 30 percent of range

    $1,182.50
    FREE shipping
    Go to shop
  19. Cdi Meters Flow Meter -Compressed Air-Systems - Copper Pipes (0.75")

    The CDI 6200 series was designed for monitoring the flow rate of compressed air systems. The flowmeter clamps onto a pipe, with two flow-sensing probes projecting into the pipe through 3/16-in. drilled holes. It seals directly to the pipe; no cutting or welding is required for installation. Because each flowmeter is made and calibrated for a specific size of pipe, the display indicates flow directly, with no setup or adjustment. The meter measures flow by maintaining one probe warmer than the other. It calculates the mass velocity from the amount of heat required, and then calculates the flow on the basis of pipe area. The flow rate, in scfm, is shown on a large, four-digit display; a 4-20 mA output and a pulse output permit remote display, totalizing and data collection. Features: - Easy to install - Housing and display rotate to suit piping orientation - IP-66 rating; suitable for wet locations - Milliamp and pulse outputs - Optional RS-485 output for networking Specifications: - Accuracy: 5 percent of reading plus 1 percent of range for flows from 10 percent to 100 percent of indicated range at air temperatures between 20 and 120 degrees Fahrenheit. - Fluids: Compressed Air, Nitrogen - Range: 150 scfm - Operating Pressure (steel and copper): 200 psig maximum - Input power: 250 mA at 24 Vdc - Output resistance: 400 Ohms max. - Exposed Materials: Stainless steel, gold, thermal epoxy and Viton (seal) - Display: Four-digit LED display - Response time: One second to 63 percent of change in value at flows above 30 percent of range

    $995.50
    FREE shipping
    Go to shop
  20. Cdi Meters Cdi5200 Flow Meter For Copper Pipes (0.75")

    The CDI 5200 clamps onto a pipe, with two flow-sensing probes projecting into the pipe through 3/16-in. drilled holes. It seals directly to the pipe; no cutting or welding is required for installation. Because each flowmeter is made and calibrated for a specific size of pipe, the digital display indicates flow directly, with no setup or adjustment. The meter measures flow by maintaining one probe warmer than the other. It determines the mass flow rate from the amount of heat required. The flow rate, in scfm or equivalent units, is shown on a large, four-digit display; a 4-20 mA output and a pulse output permit remote dis-play, totalizing and data collection. Features: - Easy to install - Two-rings - No moving parts - Weather resistant and surge protected - Milliamp output - Pulse output convertible to threshold output - User-configurable scaling, filtering and units of measureSpecifications: - Accuracy: 5 percent of reading plus 1 percent of range for flows from 10 percent to 100 percent of indicated range at air temperatures between 20 and 120 degrees Fahrenheit.- Fluids: Compressed Air, Nitrogen - Range: 150 scfm- Operating Pressure (steel and copper): 200 psig maximum - Input power: 250 mA at 24 Vdc- Output resistance: 600 Ohms max.- Exposed Materials: Stainless steel, gold, thermal epoxy and Viton (seal)- Display: Four-digit LED display- Response time: One second to 63 percent of change in value at flows above 30 percent of range

    $891.00
    FREE shipping
    Go to shop
Back to top

Recently Viewed Plumbing Accessories & Fittings


Connect
Getprice compares prices across all of your favourite products Australia-wide, covering all major cities including Sydney, Melbourne, Perth, Canberra and Brisbane.
Getprice compares prices across Sydney, Melbourne, Perth, Canberra and Brisbane.