Stratco Roof & Gutter | Best Prices in Australia | GetPrice
Showing 1 - 20 of 244 results for

Stratco Roof & Gutter

Sort:
  1. Quad Gutter Hi-Front CB 115mm 135 Deg Corner
    + Shipping
  2. Quad Gutter Lo-Front Zinc 115mm Ext Bracket
    + Shipping
  3. The effective of each sheet is 762mm. The minimum recommended roof pitch is 5 degrees 1 in 12. Enter the quantity of sheets and lengths eg: 12/2400 6/3000 Add up the total lineal metres qty x the length for each sheet and multiply by 0.762 to find the m2 Corrugated sheeting is cut to lengths that suit your specific requirements. All sheets must be longer than 1.2m but can be cut to any length provided satisfactory transport and handling facilities can be arranged. Painted head screws or coloured caps for Type 17 and Tek Screws are available as well as a complete range of accessories and flashings.
    + Shipping
  4. Stratco 125mm OG Gutter
    + Shipping
  5. Stratco purlins are crisp, clean and square and by any assessment are a quality product. There is no need to tolerate rounded corners, inaccurate lengths, or out of square purlins any more. Technical Drawings will be required if you need punching (no extra for this) - please advise in the notes section of your enquiry if this is required
    + Shipping
  6. Stratco purlins are crisp, clean and square and by any assessment are a quality product. There is no need to tolerate rounded corners, inaccurate lengths, or out of square purlins any more. Technical Drawings will be required if you need punching (no extra for this) - please advise in the notes section of your enquiry if this is required
    + Shipping
  7. Stratco purlins are crisp, clean and square and by any assessment are a quality product. There is no need to tolerate rounded corners, inaccurate lengths, or out of square purlins any more. Technical Drawings will be required if you need punching (no extra for this) - please advise in the notes section of your enquiry if this is required
    + Shipping
  8. Stratco purlins are crisp, clean and square and by any assessment are a quality product. There is no need to tolerate rounded corners, inaccurate lengths, or out of square purlins any more. Technical Drawings will be required if you need punching (no extra for this) - please advise in the notes section of your enquiry if this is required
    + Shipping
  9. Barge capping is the typical flashing piece used to finish off any roofing profile with the edge of the wall and runs down the length of the roof sheeting it is finishing off. Typically the barge flashing should be at least 40-50mm longer than the specified roof length to allow for the angle cutting at the top of the roof line and even longer if being used to continue past the gutter at the end of the roof sheets.
    + Shipping
  10. Stratco purlins are crisp, clean and square and by any assessment are a quality product. There is no need to tolerate rounded corners, inaccurate lengths, or out of square purlins any more. Technical Drawings will be required if you need punching (no extra for this) - please advise in the notes section of your enquiry if this is required
    + Shipping
  11. Stratco purlins are crisp, clean and square and by any assessment are a quality product. There is no need to tolerate rounded corners, inaccurate lengths, or out of square purlins any more. Technical Drawings will be required if you need punching (no extra for this) - please advise in the notes section of your enquiry if this is required
    + Shipping
  12. Stratco purlins are crisp, clean and square and by any assessment are a quality product. There is no need to tolerate rounded corners, inaccurate lengths, or out of square purlins any more. Technical Drawings will be required if you need punching (no extra for this) - please advise in the notes section of your enquiry if this is required
    + Shipping
  13. Stratco purlins are crisp, clean and square and by any assessment are a quality product. There is no need to tolerate rounded corners, inaccurate lengths, or out of square purlins any more. Technical Drawings will be required if you need punching (no extra for this) - please advise in the notes section of your enquiry if this is required
    + Shipping
  14. Stratco purlins are crisp, clean and square and by any assessment are a quality product. There is no need to tolerate rounded corners, inaccurate lengths, or out of square purlins any more. Technical Drawings will be required if you need punching (no extra for this) - please advise in the notes section of your enquiry if this is required
    + Shipping
  15. Stratco purlins are crisp, clean and square and by any assessment are a quality product. There is no need to tolerate rounded corners, inaccurate lengths, or out of square purlins any more. Technical Drawings will be required if you need punching (no extra for this) - please advise in the notes section of your enquiry if this is required
    + Shipping
  16. Stratco purlins are crisp, clean and square and by any assessment are a quality product. There is no need to tolerate rounded corners, inaccurate lengths, or out of square purlins any more. Technical Drawings will be required if you need punching (no extra for this) - please advise in the notes section of your enquiry if this is required
    + Shipping
  17. Stratco purlins are crisp, clean and square and by any assessment are a quality product. There is no need to tolerate rounded corners, inaccurate lengths, or out of square purlins any more. Technical Drawings will be required if you need punching (no extra for this) - please advise in the notes section of your enquiry if this is required
    + Shipping
  18. Rolltop ridge capping is the flashing used to finish off any gable roof that adds a little bit of the traditional style reminiscent of the older homes and styles of Australian buildings. The dimensions are close to 20/160/40 semi-circle/160/20mm. This item cannot be customised in its dimensions.
    + Shipping
  19. Stratco offer a wide range of Fluted Downpipes to suit a variety of applications. Square rectangular and round Fluted Downpipes are available to suit any style of home building or factory. Sizes available range from small drainage requirements up to large factory requirements. As a general guide in non cyclonic areas for every 10 square metres of actual roof area drained 700 square millimetres of Fluted Downpipe is required whether round or square. This calculation is based on the assumption that the maximum rainfall does not exceed 125mm per hour. It is considered the best practice to drain to different points using smaller Fluted Downpipes rather than to one large outlet. Where possible Fluted Downpipes should be spaced at not more than 12000mm centres. For a printable brochure on how to install Fluted Downpipes visit the Stratco website. or contact buybuildingsupplies.com.au
    + Shipping
  20. Stratco purlins are crisp, clean and square and by any assessment are a quality product. There is no need to tolerate rounded corners, inaccurate lengths, or out of square purlins any more. Technical Drawings will be required if you need punching (no extra for this) - please advise in the notes section of your enquiry if this is required
    + Shipping
Back to top

Recently Viewed Roof & Gutter


Connect
Getprice compares prices across all of your favourite products Australia-wide, covering all major cities including Sydney, Melbourne, Perth, Canberra and Brisbane.
Getprice compares prices across Sydney, Melbourne, Perth, Canberra and Brisbane.